![when installing my chevy fog lights which is right and left when installing my chevy fog lights which is right and left](https://www.u-buy.co.uk/productimg/?image=aHR0cHM6Ly9tLm1lZGlhLWFtYXpvbi5jb20vaW1hZ2VzL0kvNzE2Qm5LaDBnVkwuX0FDX1NMMTAwMF8uanBn.jpg)
- WHEN INSTALLING MY CHEVY FOG LIGHTS WHICH IS RIGHT AND LEFT HOW TO
- WHEN INSTALLING MY CHEVY FOG LIGHTS WHICH IS RIGHT AND LEFT DRIVERS
- WHEN INSTALLING MY CHEVY FOG LIGHTS WHICH IS RIGHT AND LEFT PROFESSIONAL
For more information on how to aim fog lights, chat with a knowledgeable expert at your local NAPA AUTO PARTS store. If you notice one light seems to be pointed in a slightly different direction than the other, simply head back to the wall and go through the process all over again.Ĭheck out all the lighting parts available on NAPA Online or trust one of our 17,000 NAPA AutoCare locations for routine maintenance and repairs. Remember: You may need to re-aim your fog lights from time to time, as the constant vibration of driving can knock them out of alignment, and so can the impact of bugs, stones and rubber out on the road. This will move the beam of light until it’s able to cut underneath fog while also avoiding the eyes of other drivers. The lights themselves were a piece of cake. Then, using the adjustment screws to wiggle and drop the aim of the fog lights about four inches under that bulls-eye. Make a small mark on the wall that is at the same height as the center of the fog lights as they are mounted on your vehicle (use the tape measure for each mark). The last step in learning how to aim fog lights is to make the small adjustments needed to keep the beams pointed at the right spot. On this forum thread, members say it could cost anywhere from 200 to 300 to have fog lights. On a forum thread at, forum members indicated that fog light installation could cost around 180 to 255.
WHEN INSTALLING MY CHEVY FOG LIGHTS WHICH IS RIGHT AND LEFT PROFESSIONAL
You’ll also need a marker and a tape measure to assist you in backing up exactly 25 feet from the wall so you can make the proper adjustments. On average, installing new fog lights with a professional mechanic will cost anywhere from 150 to as much as 450.
![when installing my chevy fog lights which is right and left when installing my chevy fog lights which is right and left](https://img.joomcdn.net/bc3476b29ac76304183fa19e8c0acaad143a9b08_original.jpeg)
To do this, you need an absolutely flat stretch of pavement with a 90-degree wall right in front of it. Once you’re got them mounted properly, it’s time to learn how to aim fog lights. The idea is to make it as simple as possible to point the fogs under that 24-inch gap that usually sits between mist and the road surface. From a mounting perspective, this means you’ll want to put them either just above or just below the bumper, no less than 10 inches off the ground but ideally no more than two feet above it, either. Not hard but it is awkward getting the bolts started.
![when installing my chevy fog lights which is right and left when installing my chevy fog lights which is right and left](https://i.ebayimg.com/images/g/f2UAAOSw0Apc24sz/s-l400.jpg)
This allows them to complement your headlights without simply throwing more light at the fog. Make sure you line up the new valance before snugging the bolts down on each end or you will have gaps. Pick the Right Mounting Spotįog lights are designed to cut under the haze in front of you and reduce glare and reflections. Check out these three basic tips that will have your fogs pointed in the right direction in no time.
WHEN INSTALLING MY CHEVY FOG LIGHTS WHICH IS RIGHT AND LEFT DRIVERS
A poorly aimed fog light doesn’t help anyone, and having it shine in the face of other drivers is a nuisance at best. Yesterday I replaced my LOW beams with Sylvania Silverstar Ultra H11 bulbs. Learning how to aim fog lights will help you not only deal with low-visibility situations out on the road, but also prevent you from accidentally blinding other motorists in the oncoming lane. Evidently, the housing in certain GM models (mine is a 2012 Equinox, but 2010-2017 are probably the same designs) with the plastic cover behind the bulb housing prevents these owners from installing LED lights.